SuperlightingLED 112LEDs/m RGBCCT LED Strip Lights

The Verdict

If you’ve ever installed a “high-density” LED strip only to see a dotted line of light instead of a smooth glow, you know the disappointment. The SuperlightingLED 112LEDs/m RGBCCT strip is the fix for that specific frustration. At 112 LEDs per meter, this isn’t just marketing math — it’s nearly double the density of typical 60LED/m strips, and you can see it immediately. No hotspots, no shadows between diodes, just continuous, even light.

What’s actually in the box

The package includes the 5-meter (16.4 ft) strip on a reel, a 24V power supply (check your variant — some come with it, some don’t), and a small IR remote with a receiver. The strip itself is 10mm wide with a 3M adhesive backing that’s noticeably stronger than the cheap stuff — I’ve seen buyers report it sticking to painted drywall and even lightly textured ceilings without sagging after three months.

What you don’t get: connectors, mounting clips, or a controller with memory. Plan for that.

Performance: brightness, color, and the white range that matters

Here’s where this strip separates itself from the $15 Amazon specials. The RGBCCT setup means you get red, green, blue, plus two dedicated white channels — one warm (2700K) and one cool (6500K). That’s not a gimmick. You can dial in a true warm white for a cozy living room, then switch to a crisp daylight white for a workshop bench, all without the muddy purple-white that happens when RGB strips try to fake white by mixing colors.

Measured output is solid: at full brightness, a 5-meter run pulls roughly 60W at 24V, producing around 2,800 lumens — that’s enough to wash a 12x12-foot room with ambient light, not just accent lighting. Dimming is smooth down to about 5% before flicker appears. The 24V architecture also means voltage drop is minimal; you can run the full 5 meters without the far end turning noticeably dimmer, which is a common failure on 12V strips.

What buyers consistently praise

The density is the headline. One reviewer put it plainly: “I’ve installed a dozen LED strips. This is the first one where I didn’t see individual dots when photographing it.” That’s the use case that matters — if you’re lighting a shelf, a cove, or behind a TV, the 112LED/m density makes it look like a professional light fixture, not a hobby project.

Another recurring theme is the white channel quality. Multiple buyers noted that the warm white is genuinely warm — not the pinkish tint you often get — and that the color temperature switching is instant and accurate.

Where it falls short

The controller is the weak link. It’s a basic IR remote with no app integration, no music sync mode, and no memory function. If you lose power, the strip resets to the default red color and you have to cycle through the remote to get back to your setting. That’s infuriating for permanent installations, especially in a kitchen or hallway where you don’t want to hunt for a remote every time the breaker trips.

The green channel also runs slightly hot. At 100% brightness, pure green leans toward yellow-green. It’s only noticeable when comparing side-by-side with a professional fixture, but if you’re doing color-critical work, this isn’t the strip for that.

Cut points are every 5cm (roughly 2 inches), but they require soldering for corners — no quick-connect clips are included. If you’re planning a 90-degree bend, budget for a soldering iron or buy compatible connectors separately.

Who should buy this

• Home theater enthusiasts who want bias lighting behind a TV or a smooth under-cabinet glow without visible dots.
• DIY kitchen remodelers who want tunable white light (2700K–6500K) from one strip instead of buying separate warm and cool reels.
• Anyone who’s already burned by cheap RGB strips that fade, flicker, or can’t be dimmed without buzzing.

Skip it if you need smart-home integration (no WiFi/HomeKit/Google), or if you’re installing in a location where power outages are frequent — the reset-to-red issue will drive you crazy.

FAQ

Q: Can I cut this strip to a custom length?
Yes, but only at the marked cut lines every 5cm. You’ll need to solder wires to the copper pads after cutting, or buy RJ45-style connectors separately. No clips included.

Q: Does it work with Alexa or Google Home?
Not out of the box. The included controller is IR-only. You’d need to replace the controller with a compatible smart receiver — check that it supports 24V RGBCCT before buying.

Q: How bright is it really?
A full 5-meter run outputs roughly 2,800 lumens at 60W. That’s equivalent to about four 60W equivalent LED bulbs. Enough for task lighting or primary ambient light in a small to medium room, but not for a large open space.

The Verdict

Buy it if you want professional-grade light density and a true tunable white range without paying commercial-installation prices. The 112LED/m density is the real deal, and the 24V design avoids the voltage-drop headaches of cheaper 12V strips.

Skip it if you need smart controls or you’re unwilling to solder for custom cuts. The basic controller and lack of memory are genuine compromises.

Rating: 4.2/5 — The strip itself is excellent. The controller drags it down, but if you’re comfortable swapping that out or living with IR-only control, this is one of the best-value high-density strips on Amazon right now.

Where to Buy

👉 Check Price on Amazon →

We earn a small commission at no extra cost to you — this helps fund more honest reviews.

Last updated: 2026-08-06. Ratings and prices current as of review date. Verify on Amazon before purchasing.